Qinghai Province Henan Mongolian Autonomous County 2020 auto parts laser cutting machine spot exhibition
Now the laser welding production line has been revealed on a large scale in the vehicle manufacturing industry, the successful transaction through one of the outstanding achievements of the tool manufacturing industry. German audi, mercedes-benz, Volkswagen, Europa state of transportation, such as Sweden Volvo factory as early as 20 one hundred 80 period was the first to see fit and side frame using laser welding roof, car body, such as sheet metal welding, 90 times the American general motors, ford and Chrysler vehicles rushed to the introduction of the laser welding, although to go late, but development soon.
Laser processing is widely used in laser sunlight battery manufacturing: such as sunlight silicon laser cutting, sunlight water heater heat transfer plate welding. Laser processing as a kind of environmental protection, efficient processing will be more widely used in the future
So now the exposure of fiber laser cutting machine, laser cutting machine to sheet metal processing has brought great convenience and effectiveness, not only improve the efficiency, and improve the manufacturing process, which is absolutely the same as laser cutting machine in processing thickness and material.
Because the slag temperature generated by laser cutting machine is very high, laser cutting machine is through the optical system to focus the laser beam emitted by the laser to high power density. The same day, when the temperature laser cutting machine is higher than 1700 degrees, the boiling and convection of slag will be more oxygen into the lower part of the reaction zone, so that the base metal then add combustion phenomenon reaction, but the opportunity to contact with the base metal is less, because the bottom metal does not add combustion phenomenon reaction. OT produces the combustion phenomenon reaction, mainly assuming that the calories generated by the combustion phenomenon reaction will melt it, but it can not successfully achieve absolute melting, so under high atmospheric pressure, it can not discharge the attached slag.
In the process of laser head working, abnormal movement, blocking, tremor and other phenomena are revealed, which is an important research debate on the normal power supply. Fiber laser cutting machine is a laser cutting machine with fiber laser as the light source. This material situation is caused by the assumption that the supply voltage is unstable.
Single-side welding, or the pursuit of good-looking, or the pursuit of tight degree of density, pretend to be more closely connected, the demand for welding slower, then the heat will be more, the heat effect will be greater.
The maximum weldable thickness is limited and the penetration thickness of the workpiece is far more than 19mm. The production line is uncomfortable and laser welding is used.
Welding robot. Welding robot is an industrial robot dedicated to welding. Industrial robot is a multi-purpose, repeatable programmable Manipulator with three or more programmable axes for industrial automation. In order to meet different purposes, the mechanical interface of the latter axis of the robot is also a joint flange, which can be connected with different tools or end-effectors. Welding robot is installed in the end shaft flange of industrial robot welding clamp or welding (cutting) gun, so that it can weld, cut or thermal spraying.
Liquid to gas cutting. Molten cutting generally uses inert gases. Fiber laser cutting machine is a laser cutting machine with fiber laser as the light source. Assuming that oxygen or other active gases are used instead, the material is ignited under the irradiation of a laser beam, and a strong chemical reaction occurs with oxygen, producing another kind of heating object, known as oxidation melting cut.
Due to the ability to manufacture lightweight structures, the importance of superior steel in different engineering applications is becoming more and more apparent day by day. Vehicle-mounted concrete pumps use these individual alloy steels to reduce the thickness of steel plates. This can be experienced in reducing net weight or increasing load. As a rule, these individual structures are welded by hand gas welding as deemed appropriate. In this material form, multipass welding must be used as appropriate. On the one hand, high heat input causes residual stress and deformation; Bead annealing, on the other hand, often reduces the strength and toughness of the weld. Fiber laser cutting process parameters, but also caused more processing time, in the study of efficient and automated production process, feel appropriate and the use of gas welding and laser combined to make the composite welding technology. Using this technology, can single-pass welding of 3-8mm plate thickness of weld, and increase in welding speed at the same time, can prevent the deficiency mentioned above. In contrast to single laser welding, the attached unit can be used to treat the composition of the stainless steel cutting machine by the integrated wire feeding mechanism according to the requirements of superb steel. In addition to this, excitation-reduction bonding reveals the bridging properties of the core, which are critical for the fabrication of steel structures. Because of this, for different types of joints, composite welding guarantees the stability and reliability of the welding process when the hole hole is less than 1mm.
In laser cutting machine electrical products, metal sheet processing parts account for more than 30% of the whole parts.
For some strong factories, the accuracy of lead screw or guide rail is not enough. The level of technical force and workers is not high. Laser cutting machine cutting accuracy is less than 0.1mm, because the round hole cutting accuracy is not up to the requirements.
The current or voltage of the fiber laser cutting machine is too high, causing the fiber laser cutting machine disconnection.
Processing of suitable parts: production models are expensive to manufacture. Laser cutting does not require whatever production model is manufactured. It can absolutely prevent material collapse in the process of punching and shearing, reduce the cost of production, improve the grade of food machinery, food production in order to remain invincible in the international market, it must be mechanized, active, professional and extensive. We had to move away from traditional manual operations and shop floor controls. Fiber laser cutting machine is a laser cutting machine with fiber laser generator as the light source to improve health, safety and production efficiency.
Laser welding is very accurate and has a good appearance, so it is widely used in laser marking and laser welding of high-grade stainless steel bathroom products. Such as: handle, never water hose hasty head, rust eating utensils, knives and most of the way to manufacture the company LOGO with laser marking, high-grade electric kettle and other strict closed also feel appropriate and use laser welding to complete. The assembly welding butt welding of cooking utensils and eating utensils, and the repair and modification of production models in the process of manufacturing and application
Feel suitable and use Europa imported fiber laser, the use of life saving years up to 100,000 hours, after-sales quality guarantee for 2 years, to ensure the actual benefits of customers.
Laser cutting machine cutting carbon steel nozzle and lens selection fiber laser cutting machine is the fiber laser laser cutting machine as the light source
Electroslag automatic welder. Electroslag automatic welding machine is suitable and the use of welding wire electrode, welding wire through the non-consumption electroslag gun and conductive nozzle into the slag pool welding equipment. Electroslag automatic welding machine is mainly used for high efficiency welding of vertical welds of steel structures, especially for the welding of box columns and box beams.
上一個：沒有了